|
||||||||
|
||||||||
Order Status
|
| |
 |
| ||
| ||
| ||
 | Center tool gageThis new tool from Alisam Engineering, makes centering your lathe tool to your lathes axis a quick and easy task! Ideally for those jobs where you need to switch to a different tool ... | $18.99 |
| ||
| ||
| ||
 | Complete Set! Grinding jig!This is the complete set of 5 square toolbit holders, (3/16, 1/4, 5/16, 3/8 & 1/2 inch), along with the grinding block itself. SAVE 10%!! | $122.36 |
| ||
| ||
| ||
 | Dauber-13Our latest reproduction for the 13, 14 1/2 OR 16 inch South Bend lathes*! This is that little dauber or quill oiler (*same SBL part number was used for each lathe), that almost ... | $18.99 |
| ||
| ||
| ||
 | Dauber-910Our latest reproduction for the 9 OR 10 inch South Bend lathe! This is that little dauber or quill oiler that almost every lathe is missing. You can wait and try to find an ... | $17.99 |
| ||
| ||
| ||
 | Dremel tool holder 1/4" offset shankThis Dremel tool holder for your metal lathe has a 1/4" X 1/2" OFFSET shank. This allows the machinist with a fixed height tool holder on his lathe to hold a Dremel or other ... | $19.99 |
| ||
| ||
| ||
Dremel tool holder 3/8 X 1/2 inch shankThis unique metal lathe tool accessory, made from hot rolled steel, with a 3/8 X 1/2 inch shank, will allow the home shop machinist, model builder, gunsmith etc. to be able to ... | $19.99 | |
| ||
| ||
| ||
 | Dremel. tool holder 1/4" X 1/2" shankThis unique metal lathe tool accessory will allow the home shop machinist, model builder, gunsmith, custom Cue maker, (Billiards), etc. to be able to utilize their ... | $19.99 |
| ||
| ||
| ||
 | Dremel. tool holder 1/2 inch shankThis unique metal lathe tool accessory will allow the home shop machinist, model builder, gunsmith etc. to be able to utilize their Dremel® tool, (or other ... | $19.99 |
| ||
| ||
| ||
 | Dremel. tool holder 3/8" round shankThis unique metal lathe tool accessory will allow the home shop machinist, model builder, gunsmith etc. to be able to utilize their Dremel® tool, (or other moto-tool ... | $29.99 |
| ||
| ||
| ||
 | Flat belt gluing fixtureA flat belt gluing fixture for the repair or replacement of flat belts on metal lathes and other belt driven machinery. By placing the skived, glued belt between compression plates, ... | $18.99 |
| ||
| ||
| ||
 | Flex shaft tool holderThis tool holder will fit a 1/2" OD flex shaft handpiece. Has a 1/2" X 1/2" shaft to fit most QC tool holders. | $24.99 |
| ||
| ||
| ||
 | Foredom tool holderThis tool holder will fit a 1" OD Foredom handpiece or any other 1" OD flex shaft tool's handpiece. Shank is 1/2" X 1/2" to fit most QC tool holders. | $29.99 |
| ||
| ||
| ||
 | Grinding GageAlisam Engineering’s newest addition to our growing line of South Bend Lathe reproduction tools! We have faithfully reproduced the grinding gage used to check a ... | $12.50 |
| ||
| ||
| ||
 | Grinding JigThis new tool from Alisam Engineering is a reproduction* of South Bend Lathe Works cutter bit grinding block not in production for many years! Each grinding block will come with ... | $79.99 |
| ||
| ||
| ||
 | Grinding jig tool holdersTool holders for our tool bit grinding jig, (GJ-01), come in 5 different sizes, 3/16, 1/4, 5/16, 3/8 and 1/2 inch to fit most quality, ground, square modern tool ... | $16.99 |
| ||
| ||
| ||
 | Knock-out bar 1 in.This Knock-out bar will save the inside of your lathes' 1 inch ID spindle from marring while removing collets, centers or sleeves! Don't use that scrap steel bar or ... | $25.99 |
| ||
| ||
| ||
 | Knock-out bar 1.375 in.This Knock-out bar will save the inside of your lathes' 1.375 inch ID spindle from marring while removing collets, centers or sleeves! Don't use that scrap steel bar ... | $25.99 |
| ||
| ||
| ||
 | Knock-out bar 3/4 in.This Knock-out bar will save the inside of your lathes' 3/4 inch ID spindle from marring while removing collets, centers or sleeves! Don't use that scrap steel bar or the ... | $25.99 |
| ||
| ||
| ||
 | Knock-out bar brass ring for .75 inch ID spindleThis is the THREADED brass ring ONLY, for the knock-out bar we offer, (picture is of our older press fit model). This item is for use with a .75 inch ID spindle. | $6.00 |
| ||
| ||
| ||
 | Knock-out bar brass ring for 1 inch ID spindlesThis is the THREADED brass ring ONLY, for the knock-out bar we offer, (picture is of our older press fit model). This item is for use with a 1.0 inch ID spindle. | $6.00 |
| ||
| ||
| ||
 | Knock-out bar brass ring for 1.375 inch ID spindlesThis is the THREADED brass ring ONLY, for the knock-out bar we offer, (picture is of our older press fit model). This item is for use with a 1.375 inch ID spindle. ... | $6.00 |
| ||
| ||
| ||
 | Radius tool frame Concave/convexThis item is the "pre-broached", 2 inch radius tool frame assembly with a "pre-broached" concave cutting bar included. This is NOT a completed tool! | $64.99 |
| ||
| ||
| ||
 | Radius tool frame assembly 2 inchThis completly cut out frame assembly is made out of 1/2 inch high strength aluminum alloy plate. The hard work is done for you! With minimal machining this frame is ... | $36.99 |
| ||
| ||
| ||
 | Radius tool frame assembly 3/8 inchThis completely cut out frame assembly is made out of 3/8 inch high strength aluminum alloy. The hard work is done for you! With minimal machining this frame is ready to ... | $28.99 |
| ||
| ||
| ||
 | Radius tool frame, 2 inch, "pre-broached"This 2 inch model radius tool frame assembly has the 1/4 inch square hole "pre-broached" to fit most 1/4 inch square toolbits. (This is a frame assembly only, NOT a finished tool). ... | $47.99 |
| ||
| ||
| ||
| |
| |
|